Engine Specifications and Exploded View for BMW M3/S14 See “Metric Mechanic HiFlo ST M3 Head” chart on the next page. By using stock cams and porting, the engine ends up with a very flexible power band on the street. Stock camming also helps the engine pass emissions. Metric Mechanic 29.5 mm M3 Intake Ports compared [...]
Posted in BMW | Tags: BMW, Engine, Flow, stock, Valve, Valve Springs
BD Valve Body Installation Manual for Dodge Ram 2000-2004 1. Pressure testing is accomplished by inserting a fitting and hose assembly with a good quality gauge into the center 1/8” port on the passenger side of the transmission. Leave the gauge attached for testing later. 2. VERY IMPORTANT – Road test with gauge in place [...]
Posted in Dodge | Tags: Body, Dodge Ram, DRIVE, Engine, Gauge, Installation, manual, pressure, test, Transmission, Valve
Step by Step Trans-Brake Installation Guide Ford C-4 The transmission must be properly rebuilt for racing before installation of this Trans-Brake. See attached diagram for the necessary modification. It is necessary for two ¼” vent holes to be drilled behind the servo in the case as shown. Remove and inspect the Forward drum, making sure [...]
Posted in Ford | Tags: Body, Brake, case, ford, Guide, Installation, modulator, Step, torque, Transmission, Valve
Complete Part List for Dodge Truck Magnum / Jeep Engines Bolt-on a set of new Mopar 5.7L Hemi Ram Exhaust Headers and you will feel and hear the power of your legendary engine like never before. Available for 2WD and 4WD models, nothing beats the best. Try not to scare the kids! ENGINES AND BLOCK [...]
Posted in Dodge, Jeep | Tags: air, Dodge Truck, Engine, Engines, Flywheel, Jeep, L Hemi, List, Magnum, Mopar, part, Valve
Workshop Manual 2002 Mazda MX-5 Circuit Open/Short Inspection Open circuit – Power circuit (IAC valve connector terminal A and PCM connector terminal 2P) – GND circuit (IAC valve connector terminal B and PCM connector terminal 2Q) VARIABLE TUMBLE CONTROL SYSTEM (VTCS) CHECK VALVE (ONE-WAY), DELAY VALVE INSPECTION A5U011313995W02 1. Remove the VTCS check valve (one-way) [...]
Posted in Mazda | Tags: Circuit, connector, Inspection, Installation, Mazda, Removal, System, terminal, Valve, VTCs
Specific Trouble Codes Hyundai.pdf P1131 Injection Quantity Adjust P1134 O2s Transition Time(B1/S1) P1135 Injection Timing Servo P1140 Inlet Air Temperature Sensor Malfunction P1141 Slow Duty Solenoid- Malfunction P1145 Main Duty Solenoid- Malfunction. P1171 ETS Valve Stuck – Open P1172 ETS Improper Motor Current P1173 ETS Target Following Malfunction P1174 ETS Valve Stuck – Close #1 [...]
Posted in Hyundai | Tags: ETS, malfunction, motor, Open, Valve
Auto Trans Overhaul Mitsubishi Mirage 1992 These Mitsubishi transaxles consist of transmission, torque converter, transfer assembly and differential. The F4A20 series is an electronically controlled, fully automatic 3-speed unit with an overdrive 4th gear. Lubrication and Adjustment, Troubleshooting, System Wiring Oil Temperature Sensor Throttle Position Sensor Pulse Generator “A” or “B” Pressure Control Solenoid Valve [...]
Posted in Mitsubishi | Tags: auto, control, gear, Mirage, Mitsubishi, Overhaul, solenoid, Trans, Transmission, Valve
Secondary Air Injection (AIR) system Checking Audi TT The heat produced by secondary oxidation greatly reduces start-up time for the catalytic converter, therefore improving exhaust quality during the cold start phase significantly. In the cold start phase, the ECM -2- activates the secondary air pump – 12- via the relay for Secondary Air Injection (AIR) [...]
Posted in Audi | Tags: air, Checking, combination, converter, Injection, phase, pressure, start, System, Valve
Hydraulic and Hydraulic Roller Cams Valve Adjustment Simple Guide Time to adjust valves, the most important thing to know is do one cylinder at a time starting at front and working your way around. Rotate engine directions when the exhaust valve starts to open adjust intake valve, when the intake valve opens and start to [...]
Posted in Repair Manuals | Tags: Adjustment, Cams, cylinder, Exhaust, Hydraulic, Intake, Roller, Simple, time, Valve
Procedure Guide Oilhead Valve Adjustment Each pair of intake valves will be matched, as will each pair of exhaust valves. “Surging? BMW’s officials still say that ‘surging’ is an aberration blamed on ‘techs taking shortcuts’ when doing tune-ups.” If you’ve still got the stock engine timing cover plug – go to BMW and get yourself [...]
Posted in Repair Manuals | Tags: Adjustment, BMW, Cover, Guide, Intake, Oilhead, pair, Plug, Procedure, Valve